23mA +12 / 20mA -12 4 HP / 25mm Deep Reverse Power Protection
We guarantee our products to be free from manufacturing defects (materials or workmanship) for one year from the date of the
original retail purchase (receipt or invoice required). For more information please visit www.acidraintechnology.com.
About Junction
Junction is a compact, 4 channel attenuverter, cascading mixer
and multiple designed to fine tune the control voltages in your
rack to the perfect range for their destinations. Junction can be
used as a source of fixed voltage, offset another voltage, or mix
multiple voltages together to create complex and dynamic
modulation.
Features
Each channel on Junction has a knob (1) that acts as a manual
control for the attenuverter. Center position (12 o clock) is 0V.
The first channel input (2) is normalized to +5V when no cable is
plugged into it.
A buffered copy of the input signal of the first channel is present
on all of the other inputs from from the first (2) to the last (8).
This duplication is “cascading” as shown by the arrow graphics
on the panel - if a cable is patched into any input, it “breaks” the
cascading multiple - all unpatched inputs carry the signal
present at the uppermost patched input (or +5V if no inputs are
patched). For example, if a signal is patched into the second
channel’s input (4) the third (6) and fourth (8) channel inputs
would carry a copy of the second channel’s input instead of the
first channel input.
Junction’s channels are mixed on the outputs. The output mixer
is also “cascading” - when a cable is patched into an output, it
carries a mix of it’s own output and all unpatched channel
outputs above it. For example, if only the last channel output (9)
is patched, this output will carry a mix of all of the outputs.
Patching the first channel output (3) would remove it from this
mix.
Even though Junction’s inputs cascade and outputs mix,
Junction’s output will clip at the Eurorack power rail voltages of
+12 and -12V. It is not possible to output a voltage outside of
this range, regardless of the signals patched into Junction.
1
-12 red
Junction requires a +12V / -12v power supply with a 2x5 pin ribbon cable (included). The red line of the ribbon
cable must be aligned with the -12V marking next to the module’s power header and on your case’s power
distribution board. Junction draws 23mA from the +12 rail and 20mA from the -12 rail. Please ensure you have
enough power available before installing.
Assembled in USA
Consultați aici manualul pentru Acid Rain Technology Junction, gratuit. Acest manual se încadrează în categoria Fără categorie și a fost evaluat de 1 persoane cu o notă medie de 7.5. Acest manual este disponibil în următoarele limbi: Engleză. Aveți o întrebare despre Acid Rain Technology Junction sau aveți nevoie de ajutor? Puneți întrebarea aici
Aveți nevoie de ajutor?
Aveți o întrebare despre Acid Rain Technology și răspunsul nu se află în manual? Puneți întrebarea aici. Furnizați o descriere clară și cuprinzătoare a problemei și a întrebării dvs. Cu cât problema și întrebarea dvs. sunt descrise mai bine, cu atât le va fi mai ușor celorlalți proprietari Acid Rain Technology să vă ofere un răspuns bun.
Nu puteți găsi răspunsul la întrebarea dvs. în manual? Puteți găsi răspunsul la întrebarea dvs. în Întrebările frecvente despre Acid Rain Technology Junction de mai jos.
Este manualul Acid Rain Technology Junction disponibil în Română ?
Din păcate, nu avem manualul pentru Acid Rain Technology Junction disponibil în Română. Acest manual este disponibil în Engleză .
Aveți nevoie de ajutor?
Aveți o întrebare despre Acid Rain Technology și răspunsul nu se află în manual? Puneți întrebarea aici. Furnizați o descriere clară și cuprinzătoare a problemei și a întrebării dvs. Cu cât problema și întrebarea dvs. sunt descrise mai bine, cu atât le va fi mai ușor celorlalți proprietari Acid Rain Technology să vă ofere un răspuns bun.
Numărul de întrebări: 0