Manual de utilizare FeiYu-Tech FY-G4

FeiYu-Tech FY-G4
  • Nr. pagini: 2
  • Tipul fișierului: PDF
FY-G4 is suitable for GoPro 4/GroPro 3+/GroPro 3, also can be compatible
with GoPro LCD backpack and the cameras with the same size.
Video Input
Pitch Axis
Roll Axis
Heading Axis
M2 Knurled
Thumb Screw
If the indicator light flashes red,
the Gimbal will not work correctly
due to an error.
Please install the suitable camera first before power on the Gimbal.
Please upgrade the firmware to V1.13 or above version.
Attention !
Beginner Guide
Product Appearance Instructions
Standard And Optional Accessories
Operation Instructions
Special Working Condition (Inversion Mode)
When in any working mode, press the function button for three times in succession, the
Gimbal enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited
scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset
the Gimbal back to the original state.
Manual Pulling Locking
The pitching can be adjusted 8 seconds after the Gimbal has been started. Within the Heading Follow and Heading
Lock Mode the pitching can be adjusted to the desired angle manually, wait in this position up to 0.5 second until the current angle is adjusted.
Standby Mode
Press the function button for 3 seconds, then the motor will stop working and the LED of the function button will light constantly.
This indicates that the Gimbal is in the standby mode. Single press the function button the Gimbal will be awakened immediately.
Level Calibration
The pitch and roll angle can be adjusted to level by G4 Remote Control without connect to the computer. Details of the
operation please refer to chapter
Heading Follow Speed Mode Configuration
The follow speed of the heading can be configurate by G4 Remote Control without
connect to the computer. Details of the operation please refer to chapter
Four press the function button in succession within any working mode, the gimbal will reset to the original state.
Input: DC 5V Min 800mA
Output: DC 4.2V
Type: 16340/18350
Power Adapter European Standard ConnectorUSB Cable
USB ConnectorExtension Knurled Thumb Screw
Correct Method For Using USB Data Cable
Battery Charging:
Connect The Computer:
Put the Mini-USB terminal of the USB
cable into the Mini-USB interface of the charger and the
USB terminal to the power adapter, if needed connect to
the EN Connector.
Please remove the batteries first,
then insert the Mini-USB terminal into the function interface on the
Gimbal and the USB terminal to the USB connector. Afterwards
connect the device with the computer to do firmware updates or
parameter configuration. (Please connect the USB cable to the
computer with the USB connector, otherwise the interface of
the computer will be damaged ).
Further information can be found in the chapter of the
Function Interface Instructions.
Extension Bar
Charging Cable
Video Output
Realize the heading & pitch angle adjustment,
mode switching, level calibration and heading
follow speed configuration from a distance.
Extend the capacity space for battery to
make the runtime longer.
Spiral design of the extension bar can be
perfect combination with G4 power switch;
Extended length is optional, it will help to
enjoy a different visual easily.
The Gimbal can power supply for the Gopro
Through this cable the analog video signal of
the Gopro camera will be send to the function
interface on the Gimbal.
Function Description
Please refer to the method of proper usage
mentioned below. Otherwise the device
itself or other equipment can be damaged
Optional Accessories
Please connect the analoy monitor for displaying
Standard Accessories
Indicator Explanation
LED Status
Blue light flashes
three times
Full Power
Blue light flashes
Enough Power
Blue light flashes
Low Power
Blue light keeps
No Power
Type: 18350
Rechargeable Battery
If any comments or suggestions please do not hesitate
to e-mail us directly :
Please choose one way
to install the GoPro camera
Insert The Batteries
Remove the power switch
cap, insert two 18350
batteries into the handle.
Install The Camera
Install the GoPro camera by the
special Thumb Screw. And make
sure it is fixed well.
Power On
Confirm the camera is
installed well,then press
the power button to turn
on the Gimbal.
Mode Switching
When the Gimbal is working, you
can press the function button to
switch among the three working
modes and a special working
condition freely.
(Details of working modes please refer
to the instructions of working modes)
Function Button Working Mode Instructions
Double Press
Single Press
Long Press
For 1 Second
LED Status
Single Flashes
Double Flashes
On Constantly
Function Explanation
Operation Again
Function Of Operation Again
Heading Follow Mode
Heading And Pitch Follow Mode
Three Press Three Press again
Other operation is arbitrary
Other operation is arbitrary
Other operation is arbitrary
Other operation is arbitrary
Single press again
Single Flashes Inversion Mode Exit inversion mode to original state
Exit standby mode ,
and awaken immediately
Heading Lock Mode
Long Press
For 3 Second
On Constantly
Standby Mode
Four Press Single Flashes Reset
Function Button Instructions
Heading, Pitch and Roll are all locked to
Use for switch
the working
mode and
realize other
The working mode and function
can be identified by the LED status
Heading Follow Mode
Camera Pitch and Roll Angles remain
Heading And Pitch Follow Mode Camera Roll Angle remains
Heading Lock Mode
constant, heading follows the handheld position.
constant. Heading and Pitch follow the handheld position.
point at one position.
FeiYu-Tech FY-G4

Aveți nevoie de ajutor?

Numărul de întrebări: 0

Aveți o întrebare despre FeiYu-Tech FY-G4 sau aveți nevoie de ajutor? Puneți-vă întrebarea aici. Oferiți o descriere clară și cuprinzătoare a problemei și a întrebării dvs.. Cu cât oferiți mai multe detalii pentru problema și întrebarea dvs., cu atât va fi mai ușor pentru ceilalți proprietari FeiYu-Tech FY-G4 să răspundă corect la întrebarea dvs..

Consultați aici manualul pentru FeiYu-Tech FY-G4, gratuit. Acest manual se încadrează în categoria Alte accesorii camera și a fost evaluat de 2 persoane cu o notă medie de 8.6. Acest manual este disponibil în următoarele limbi: Engleză. Aveți o întrebare despre FeiYu-Tech FY-G4 sau aveți nevoie de ajutor? Puneți întrebarea aici

Specificații FeiYu-Tech FY-G4

Brand FeiYu-Tech
Model FY-G4
Produs Alt accesoriu camera
Limbă Engleză
Tipul fișierului PDF
Greutate şi dimensiuni
Greutate 265 g
Lungime 239 milimetri
Lățime 65 milimetri
Înălţime 75 milimetri
Datele de ambalare
Greutatea pachetului 750 g
Compatibilitate Gopro 4/3+/ 3
Culoarea produsului Negru
Conţinutul de ambalaje
Număr de baterii incluse 2 buc.
Afișați mai multe

Întrebări frecvente

Mai jos, veți găsi cele mai frecvente întrebări despre FeiYu-Tech FY-G4 .

Întrebarea dvs. nu se regăsește aici? Puneți întrebarea aici