Manual de utilizare Honeywell RTH230B

Honeywell RTH230B
9.2 · 2
PDF manual
 · 4 pagini
Engleză
manualHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Consultați aici manualul pentru Honeywell RTH230B, gratuit. Acest manual se încadrează în categoria termostate și a fost evaluat de 2 persoane cu o notă medie de 9.2. Acest manual este disponibil în următoarele limbi: Engleză. Aveți o întrebare despre Honeywell RTH230B sau aveți nevoie de ajutor? Puneți întrebarea aici

Aveți nevoie de ajutor?

Aveți o întrebare despre Honeywell și răspunsul nu este în manual?

  • Primiți actualizări despre soluții
  • Obțineți răspunsuri la întrebarea dvs

Întrebare și răspuns

Numărul de întrebări: 0

Termostatul Honeywell RTH230B este un dispozitiv de control al temperaturii din locuință, ușor de utilizat, capacitatea lui fiind de a regla temperatura în diverse locații cu ajutorul programelor zilnice de încălzire și răcire. Acest termostat este compatibil cu majoritatea sistemelor de încălzire și răcire utilizate în case și locuințe, oferind o flexibilitate maximă utilizatorilor. Dispune de un ecran LCD mare, ușor de citit, care afișează temperatura actuală și programul stabilit de utilizator. În plus, acest termostat are o tastatură ușor de utilizat și poate fi setat cu ușurință pentru a permite utilizatorilor să își stabilească propriul program de încălzire și răcire conform nevoilor lor. De asemenea, termostatul Honeywell RTH230B are o interfață personalizată care permite utilizatorilor să regleze temperatura conform propriilor preferințe și nevoi. Aceasta poate fi utilizată pentru a stabili programul de încălzire / răcire pentru mai mult de 7 zile în avans, reducând astfel timpul și efortul necesare pentru a seta temperatura optimă în fiecare zi. Toate aceste caracteristici, combinate cu o construcție de înaltă calitate și o mare fiabilitate, fac ca termostatul Honeywell RTH230B să fie o alegere excelentă pentru a asigura confortul și economia în locuința dvs.

General
BrandHoneywell
ModelRTH230B
Produstermostat
LimbăEngleză
Tipul fișieruluiManual de utilizare (PDF)

Nu puteți găsi răspunsul la întrebarea dvs. în manual? Puteți găsi răspunsul la întrebarea dvs. în Întrebările frecvente despre Honeywell RTH230B de mai jos.

Unde este cea mai bună locație pentru amplasarea termostatului?

Cel mai bun loc pentru termostat este camera în care petreceți cel mai mult timp, în multe cazuri camera de zi sau bucătăria. Așezați termostatul la aproximativ un metru și jumătate deasupra podelei, nu la soare și nu pe un perete exterior.

Ce este banda moartă a unui termostat?

Dacă termostatul dvs. are o bandă moartă, instalația dvs. este, ca să spunem așa, „în repaus”. Termostatul pornește numai atunci când, de exemplu, diferența se abate mai mult de 2˚C de la temperatura setată a camerei.

Care este temperatura ideală a camerei?

Majoritatea oamenilor consideră că temperatura ideală a camerei este cuprinsă între 19 și 22 de grade Celsius.

Este manualul Honeywell RTH230B disponibil în Română ?

Din păcate, nu avem manualul pentru Honeywell RTH230B disponibil în Română. Acest manual este disponibil în Engleză .

Întrebarea dvs. nu se regăsește aici? Puneți întrebarea aici

Fără rezultate