Name: Magnum Standard Control
Brand: Magnum
SKU: 846663
Rating: 92 (1 reviews)

manualMagnum Standard Control

MAGNUM Standard Control

On/O Thermostat

Installation manual

PLEASE READ THIS MANUAL CAREFULLY BEFORE

INSTALLATION, AND STORE WITH OTHER WARRANTEE

FORMS.

The MAGNUM Standard Control is an electronic thermostat

with four functions: Room sensor, oor sensor, power regulator

and room sensor with max./min. limiter. This thermostat can

also be set up for setback temperature.

1. Startup

Remove the adjustment wheel with a screwdriver. The front cover

can the be removed by pushing in the locking clips on each side

of the thermostat (as shown in g.2). Be careful when doing this

in order not to damage the thermostat. When the thermostat has

been connected to the power source, push the on/o button.

Never dismantle the thermostat when the power is switched on.

2. Sensor choice

When choosing a sensor type, the thermostat should not be

connected to a power source.

• Floor sensor (standard)

Jumper placement: Covering the two pins on the left.

Application: The temperature is regulated by the oor sensor.

• Room sensor

Jumper placement: Covering the two pins in the right

Application: The temperature is regulated by the room sensor.

• Room sensor with limiter

Jumper placement: Covering the two pins on the right + the

oor sensor connected

Application: The temperature is regulated by the room sensor,

but the oor sensor overrides the room sensor if the oor

temperature exceeds the maximum limit temperature. The limiter

can be regulated between 20°C and 30°C. For parquet ooring, a

maximum of 27°C is recommended by most ooring manufac-

turers. Please follow the recommendations provided by your

manufacturer.

• Power regulator

Jumper placement: Covering the two center pins

Application: The eect regulator has a 30 min cycle. The desired

on/o interval can be set from 0 to 10, where each level increases

the on-time by 3 minutes.

Example: When the thermostat is set to level 3, the heating

element is switched on for 9 minutes, then o for 21 minutes in

the 30 minute cycle. If the thermostat is set to level 6, the heating

element is switched on for 18 minutes, then o for 12 minutes.

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING L

SENSOR

PILOT WIRE

HEATING N

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING L

SENSOR

PILOT WIRE

HEATING N

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING L

SENSOR

PILOT WIRE

HEATING N

3. Connecting the thermostat

The termostat must be connected to the power source according to

the connection diagram. All heating systems must be equipped with

a residual current disrupter with 30mA. Max load for the thermostat is

16A/3600W at 230V. If the load is higher, the thermostat must be con-

nected to a contactor. The thermostat does not have galvanic insulation

between high and low current. The sensor must therefore be considered

as live (230V) and needs to be installed in accordance with the rules for

high current installations and national installation requirements.

Caution: When reattaching the thermostat cover, make sure the ven-

tilation on the top and bottom of the thermostat is not covered up.

4. Setback temperature

The Multireg thermostat does not have a built-in setback temperature

option, but by connecting an external timer to the S and L clamps, the

temperature can be lowered by 3°C at desired times.

5. Calibrating the temperature

When connecting the oor heating system for the rst time, the tem-

perature should be set at a maximum of 15°C to 20°C. The thermostat

should be calibrated after 2-3 days. Pull out the adjustment wheel

carefully (without turning it) until it comes loose. Use a thermometer to

check the actual temperature, and push the adjustment wheel back onto

the thermometer in accordance with the measured temperature. If the

oor heating has been switched o during the summer, this procedure

should be repeated when it is switched back on.

6. Bi-LED diode

• Green light when the thermostat is in a standby mode.

• Constant red light when the relay is engaged and the power is on.

• Blinking red light when there is a sensor malfunction or the oor sensor

is disconnected.

7. Technical data

Voltage 230 VAC AC ± 15% 50 Hz

Max. load 3600W (resistive load)

Max. current 16 Amp

Power consumption 0,5W

IP-class IP 21

Power regulator Time cycle: 0-30 min

Min/Max inst. temp. -20°C - +60°C

Min/Max oper. temp. 0° - 50°C

Temperature intervals Floor sensor: 5°C - 40°C

Room sensor 5°C - 40°C

Hysteresis 0.5°C

Sensor values 0°C 29,1 Kohm

10°C 18,6 Kohm

15°C 15,1 Kohm

20°C 12,2 Kohm

25°C 10,0 Kohm

Switch 2-pole switch

Colors White RAL 9010 (5430333)

White RAL 9003 (5430444)

Floor sensor Length 3 meters. The cable can be extended

10 meters by using a proper installation cable.

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING

SENSOR

PILO

T WIRE

HEATING

Torque: Max. 2Nm

Clamp 1+ 2Sensor - Floor sensor

Clamp 3: Pilot wire (connected to L for

setback temperature)

Clamp 4: Heating L

Clamp 5: L

Clamp 6: Heating N

Clamp 7: N

Fig.2

Bi-LED diode

Adjustment wheel

Fig.1

123 4567

HEATING L

SENSOR

PILOT WIRE

HEATING N

Consultați aici manualul pentru Magnum Standard Control, gratuit. Acest manual se încadrează în categoria termostate și a fost evaluat de 1 persoane cu o notă medie de 9.2. Acest manual este disponibil în următoarele limbi: Engleză. Aveți o întrebare despre Magnum Standard Control sau aveți nevoie de ajutor? Puneți întrebarea aici

Aveți nevoie de ajutor?

Aveți o întrebare despre Magnum și răspunsul nu se află în manual? Puneți întrebarea aici. Furnizați o descriere clară și cuprinzătoare a problemei și a întrebării dvs. Cu cât problema și întrebarea dvs. sunt descrise mai bine, cu atât le va fi mai ușor celorlalți proprietari Magnum să vă ofere un răspuns bun.

Ioan Balazs • 18-2-2023Fără comentarii

Ce sa fac an situatia asta

Vezi fotografia

Răspundeți la întrebare

Balasz Ioan • 18-2-2023Fără comentarii

Am un Magnum MRC si mia funtionat perfect cam 3 luni dupa aia mia aparut pe ecran esec senzor pardoseala Sincer lam desfacut si mia fost piscat cablul de termostat lam taiat cam 5 cm si lam pus la loc si acum ami arata ca am 45C*Dar acum nu funtioneaza si e rece an camera

Vezi fotografia

Răspundeți la întrebare

Stoian vasile • 13-2-2022Fără comentarii

Când este lucrează termostatul magnum control,când estepornit ledul rosu sau cel verde?

Răspundeți la întrebare

Numărul de întrebări: 3

General

	Magnum
	Standard Control
	termostat
	Engleză
	Manual de utilizare (PDF)

Nu puteți găsi răspunsul la întrebarea dvs. în manual? Puteți găsi răspunsul la întrebarea dvs. în Întrebările frecvente despre Magnum Standard Control de mai jos.

Unde este cea mai bună locație pentru amplasarea termostatului?

Cel mai bun loc pentru termostat este camera în care petreceți cel mai mult timp, în multe cazuri camera de zi sau bucătăria. Așezați termostatul la aproximativ un metru și jumătate deasupra podelei, nu la soare și nu pe un perete exterior.

Ce este banda moartă a unui termostat?

Dacă termostatul dvs. are o bandă moartă, instalația dvs. este, ca să spunem așa, „în repaus”. Termostatul pornește numai atunci când, de exemplu, diferența se abate mai mult de 2˚C de la temperatura setată a camerei.